CCNA 1 Chapter 2 v5.03 Exam Answers 2016

CCNA 1 Chapter 2 v5.03 Exam Answers 2016

1.

Refer to the exhibit. A switch was configured as shown. A ping to the default gateway was issued, but the ping was not successful. Other switches in the same network can ping this gateway. What is a possible reason for this?

The default gateway address must be 192.168.10.1.
The ip default-gateway command has to be issued in the VLAN interface configuration mode.
The VLAN IP address and the default gateway IP address are not in the same network.
The no shutdown command was not issued for VLAN 1.
The local DNS server is not functioning correctly.

2.
While trying to solve a network issue, a technician made multiple changes to the current router configuration file. The changes did not solve the problem and were not saved. What action can the technician take to discard the changes and work with the file in NVRAM?

Issue the reload command without saving the running configuration.
Close and reopen the terminal emulation software.
Delete the vlan.dat file and reboot the device.
Issue the copy startup-config running-config command.

3.
Why is it important to configure a hostname on a device?

to allow local access to the device through the console port
a Cisco router or switch only begins to operate when its hostname is set
to identify the device during remote access (SSH or telnet)
a hostname must be configured before any other parameters

4.
Which procedure is used to access a Cisco 2960 switch when performing an initial configuration in a secure environment?

Use the console port to locally access the switch from a serial or USB interface of the PC.
Use Secure Shell to remotely access the switch through the network.
Use Telnet to remotely access the switch through the network.
Use the AUX port to locally access the switch from a serial or USB interface of the PC.

5.
What criterion must be followed in the design of an IPv4 addressing scheme for end devices?

Each local host should be assigned an IP address with a unique network component.
Each IP address must match the address that is assigned to the host by DNS.
Each IP address must be unique within the local network.
Each IP address needs to be compatible with the MAC address.

6.
A network administrator needs to keep the user ID, password, and session contents private when establishing remote CLI connectivity with a switch to manage it. Which access method should be chosen?

AUX
SSH
Console
Telnet

7.
Which interface allows remote management of a Layer 2 switch?

the switch virtual interface
the console port interface
the AUX interface
the first Ethernet port interface

8.
What is a result of using the service password-encryption command on a Cisco network device?

All passwords in the configuration are not shown in clear text when viewing the configuration.
The command encrypts the banner message.
The command encrypts the enable mode password.
A network administrator who later logs into the device will be required to enter an administrator password in order to gain access to the Cisco device.

9.
Match the difinitions to their respective CLI hot keys and shortcuts.

Tab -> Completes abbreviated commands and parameters

Ctrl-R -> returns directly to the privileged EXEC mode
Up Arrow -> scrolls backwards through previously entered commands
Ctrl-Z -> cancels any command currently being entered and returns directly to privileged EXEC mode
Ctrl-C -> Redisplays, on a new line, the command currently being typed

Other answer.

The shortcuts with their functions are as follows:
Tab –> Completes the remainder of a partially typed command or keyword
Space bar –> displays the next screen
? –> provides context-sensitive help
Up Arrow –> Allows user to scroll backward through former commands
Ctrl-C –> cancels any command currently being entered and returns directly to privileged EXEC mode
Ctrl-Shift-6 –> Allows the user to interrupt an IOS process such as ping or traceroute

10.
A network administrator is planning an IOS upgrade on several of the head office routers and switches. Which three questions must be answered before continuing with the IOS selection and upgrade? (Choose three.)

What models of routers and switches require upgrades?
Do the routers and switches have enough RAM and flash memory for the proposed IOS versions?
What ports are installed on the routers and switches?
Are the devices on the same LAN?
What features are required for the devices?
Do the devices have enough NVRAM to store the IOS image?

11. What benefit does DHCP provide to a network?

Hosts can connect to the network and get an IP address without manual configuration.
Duplicate addresses cannot occur on a network that issues dynamic addresses using DHCP and has static assignments.
DHCP allows users to refer to locations by a name rather than an IP address.
Hosts always have the same IP address and are therefore always reachable.

12.
Which two functions are provided to users by the context-sensitive help feature of the Cisco IOS CLI? (Choose two.)

providing an error message when a wrong command is submitted
allowing the user to complete the remainder of an abbreviated command with the TAB key
displaying a list of all available commands within the current mode
selecting the best command to accomplish a task
determining which option, keyword, or argument is available for the entered command

13.
A router has a valid operating system and a configuration stored in NVRAM. When the router boots up, which mode will display?

global configuration mode
user EXEC mode
setup mode
ROM monitor mode

14.
Which two features are characteristics of flash memory? (Choose two.)

Flash receives a copy of the IOS from RAM when a device is powered on.
Flash provides nonvolatile storage.
The contents of flash may be overwritten.
Flash is a component in Cisco switches but not in Cisco routers.
The contents of flash may be lost during a power cycle.

15.
Passwords can be used to restrict access to all or parts of the Cisco IOS. Select the modes and interfaces that can be protected with passwords. (Choose three.)

boot IOS mode
Ethernet interface
privileged EXEC mode
VTY interface
console interface
router configuration mode

16.
Why would a Layer 2 switch need an IP address?

to enable the switch to send broadcast frames to attached PCs
to enable the switch to function as a default gateway
to enable the switch to receive frames from attached PCs
to enable the switch to be managed remotely

17.
What is a user trying to determine when issuing a ping 10.1.1.1 command on a PC?

if there is connectivity with the destination device
what type of device is at the destination
if the TCP/IP stack is functioning on the PC without putting traffic on the wire
the path that traffic will take to reach the destination

18.
What command can be used on a Windows PC to see the IP configuration of that computer?

ping
show interfaces
show ip interface brief
ipconfig

19.
Which statement is true about the running configuration file in a Cisco IOS device?

It should be deleted using the erase running-config command.
It is automatically saved when the router reboots.
It affects the operation of the device immediately when modified.
It is stored in NVRAM.

20.
Match the description to the common IOS CLI access method.

21.
Which two characters are allowed as part of the hostname of a Cisco device? (Choose two.)

tab
space
question mark
numbers
underline

22.
A new network administrator has been asked to enter a banner message on a Cisco device. What is the fastest way a network administrator could test whether the banner is properly configured?

Power cycle the device.
Enter CTRL-Z at the privileged mode prompt.
Exit global configuration mode.
Exit enable mode and press Enter.
Reboot the device.

NEW ANSWERS FOR:
A new network administrator has been asked to enter a banner message on a Cisco device. What is the fastest way a network administrator could test whether the banner is properly configured?

Exit privileged EXEC mode and press Enter. *TRUE*

Exit global configuration mode.

Enter CTRL-Z at the privileged mode prompt.

Reboot the device.

Power cycle the device.

Question 21 update question and answer as per new exam.

Which two characters are allowed as part of the hostname of a Cisco device? (Choose two.)

tab

space

dash *TRUE*

numbers *TRUE*

question mark

17 thoughts on “CCNA 1 Chapter 2 v5.03 Exam Answers 2016

  1. Answer 9 is wrong. Correct aswer for “9. Match the difinitions to their respective CLI hot keys and shortcuts.” is:

    The shortcuts with their functions are as follows:
    – Tab – Completes the remainder of a partially typed command or keyword
    – Ctrl-R – Redisplays, on a new line, the command currently being typed
    – Ctrl-Z – Exits configuration mode and returns to the EXEC
    – Up Arrow – Allows user to scroll backward through former commands
    – Ctrl-C – cancels any command currently being entered and returns directly to privileged EXEC mode
    – Ctrl-Shift-6 – Allows the user to interrupt an IOS process such as ping or traceroute

  2. There is a mistake at question no.9. Here is the correct difinitions:

    Ctrl-R -> Redisplays, on a new line, the command currently being typed
    Ctrl-Z -> returns directly to the privileged EXEC mode
    Ctrl-C -> cancels any command currently being entered and returns directly to privileged EXEC mode

  3. A network administrator is planning an IOS upgrade on several of the head office routers and switches. Which three questions must be answered before continuing with the IOS selection and upgrade? (Choose three.)Correct
    Response
    Your
    Response
    Are the devices on the same LAN?Do the devices have enough NVRAM to store the IOS image?What models of routers and switches require upgrades?What ports are installed on the routers and switches?Do the routers and switches have enough RAM and flash memory for the proposed IOS versions?What features are required for the devices?

  4. about question no.9. correct ans:

    Ctrl-R –
    Redisplays, on a new line, the command currently being typed
    Ctrl-Z –
    returns directly to the privileged mode of EXEC mode
    Ctrl-C –
    cancels any command currently being entered and returns directly to privileged mode of EXEC.

  5. Okay so the picture in number 9 is correct, the info below it is not. And how does everyone notice that and no one notices that 22 doesn’t have the correct answers for options? There isn’t an “enable mode” as an option on that test question let alone that doesn’t exist period. Enable is what you use to enable exec mode, it isn’t a mode itself geniuses (i use that term lightly as there are a few replies on here that are a joke).

  6. NEW ANSWERS FOR:
    A new network administrator has been asked to enter a banner message on a Cisco device. What is the fastest way a network administrator could test whether the banner is properly configured?

    Exit privileged EXEC mode and press Enter. *TRUE*

    Exit global configuration mode.

    Enter CTRL-Z at the privileged mode prompt.

    Reboot the device.

    Power cycle the device.

  7. Correct answer
    The shortcuts with their functions are as follows:
    – Tab – Completes the remainder of a partially typed command or keyword
    – Ctrl-R – Redisplays, on a new line, the command currently being typed
    – Ctrl-Z – Exits configuration mode and returns to the EXEC
    – Up Arrow – Allows user to scroll backward through former commands
    – Ctrl-C – cancels any command currently being entered and returns directly to privileged EXEC mode
    – Ctrl-Shift-6 – Allows the user to interrupt an IOS process such as ping or traceroute

  8. Question 21 update question and answer as per new exam.

    Which two characters are allowed as part of the hostname of a Cisco device? (Choose two.)

    tab

    space

    dash *TRUE*

    numbers *TRUE*

    question mark

  9. Um administrador de rede está planejando uma atualização do IOS em vários roteadores e switches da matriz. Quais três perguntas devem ser respondidas antes de continuar com a seleção e atualização do IOS? (Escolha três.)

    Quais modelos de roteadores a switches requerem atualizações?
    Os roteadores e os switches têm memória RAM e flash suficientes para as versões propostas do IOS?
    Quais recursos são necessários para os dispositivos?

  10. Tarit Kumar Datta Gupta

    - Edit

    Reply

    Ctrl-C : Exits the configuration mode and returns to privileged EXEC mode
    Ctrl-Z : Exits the configuration mode or aborts the current command
    [Ref.: CISCO material; Chapter 02]

  11. question 9
    the correct answer is :

    The shortcuts with their functions are as follows:
    – Tab – Completes the remainder of a partially typed command or keyword
    – Ctrl-R – Redisplays, on a new line, the command currently being typed
    – Ctrl-Z – Exits configuration mode and returns to the EXEC
    – Up Arrow – Allows user to scroll backward through former commands
    – Ctrl-C – cancels any command currently being entered and returns directly to privileged EXEC mode
    – Ctrl-Shift-6 – Allows the user to interrupt an IOS process such as ping or traceroute

Add Comment